Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
en:vproduct:floor-coverings [2025/08/04 12:08] – ↷ Links angepasst, weil Seiten im Wiki verschoben wurden 172.21.0.1en:vproduct:floor-coverings [2025/08/18 16:04] (current) – adminwiki
Line 6: Line 6:
 //Note: When visualising virtual content, in this case the floor covering, the virtual content is always displayed before the real content. The room should therefore be empty if possible. Otherwise you could walk in front of these objects. So be careful when moving around the room with VR glasses on.// //Note: When visualising virtual content, in this case the floor covering, the virtual content is always displayed before the real content. The room should therefore be empty if possible. Otherwise you could walk in front of these objects. So be careful when moving around the room with VR glasses on.//
  
-For measuring you need: +==== Requirements ==== 
-  * The visualiser product 'Floor Creator' + 
-  * A VR headset (Meta Quest 3 or 3s), see [[en:requirements#hardware]]+To measure you need: 
 +  * The visualiser product 'Flooring Editor' 
 +  * A VR headset (Meta Quest 3 or 3s), see [[en:requirements#Hardware]]
   * The Logitech MX Ink Controller   * The Logitech MX Ink Controller
   * A room that is sufficiently lit   * A room that is sufficiently lit
  
-How to measure a room:+==== Measure the room ==== 
 + 
 +This is how you measure a room:
   - Make sure you can comfortably reach every corner of the room with the pen in your hand   - Make sure you can comfortably reach every corner of the room with the pen in your hand
-  - Open the visualiser product 'Floor Creator' in your headset browser+  - Open the visualiser product 'Floor Covering Editor' in your headset browser
   - Take the left standard controller in your left hand and the Logitech MX Ink controller in your right hand   - Take the left standard controller in your left hand and the Logitech MX Ink controller in your right hand
   - //Note: The right standard controller must remain close to you (e.g. in the same room).//   - //Note: The right standard controller must remain close to you (e.g. in the same room).//
-  - Start the 'Floor Creator' by clicking on ''Get started now'' in the tool area on the right-hand side+  - Start the room measurement by clicking on ''Start now'' in the tool area on the right-hand side
   - Select the 'AR' item in the screen dialogue that opens   - Select the 'AR' item in the screen dialogue that opens
   - Now go to any corner of the room   - Now go to any corner of the room
-  - Hold the tip of the pen in a corner of the room and press the back button on the pen to set a measuring point+  - Hold the tip of the pen in a corner of the room and press the back button on the pen to set a measurement point
   - Go clockwise or anti-clockwise to the next corner and set another measuring point   - Go clockwise or anti-clockwise to the next corner and set another measuring point
   - Continue in the selected direction until you have marked all corners of the room with a measuring point.   - Continue in the selected direction until you have marked all corners of the room with a measuring point.
-  + 
-While you are setting the measuring points, you will see a translucent red area on the floor. This is the area to which you can assign a floor covering (a texture). To do this, go back to the main menu and select the 'Texture' menu item.+While you are setting the measuring points, you will see a translucent red area on the floor. This is the area to which you can assign a floor covering (a texture). 
 + 
 +==== Modes for the measuring points ==== 
 + 
 +Read more about the [[en:vproduct:room-measure:modes|measuring point modes for the measurement.]] 
 + 
 +==== Select floor covering ==== 
 + 
 +Go back to the main menu and select the 'Texture' menu item.
  
 You can go back to editing the floor at any time and move the measuring points, insert new ones or remove them. You can go back to editing the floor at any time and move the measuring points, insert new ones or remove them.
Line 30: Line 42:
 If the measuring tape {{vproduct:pasted:20250115-153210.png}} is activated in the 'Floor Creator', you will see all distance measurements. These are displayed on the floor between the measuring points. If the measuring tape {{vproduct:pasted:20250115-153210.png}} is activated in the 'Floor Creator', you will see all distance measurements. These are displayed on the floor between the measuring points.
  
-The floor coverings displayed are differentiated by producer and are divided into [[info:flooring-categories|categories]].+The floor coverings displayed are differentiated by producer and are divided into [[en:info:flooring-categories|categories]]. 
 + 
 +==== Data export ==== 
 + 
 +{{page>en:vproduct:room-measure:export&firstseconly&noheader}} 
 + 
 +